Breaking

Thursday, 13 April 2017

EHS Alert - Arc welding

EHS Alert - Arc welding safety




Arc welding is a type of welding that uses a welding power supply to create an electric arc between an electrode and the base material to melt the metals at the welding point. They can use either direct (DC) or alternating (AC) current and consumable or non-consumable electrodes.

Before starting actual arc welding, the operator should be fully aware of the dangers involved. The high temperature arc and hot metal can cause severe burns. In addition the electric arc itself provides Health & safety hazard.

When welding with the electric arc, there is added danger that the small globules or droplets of molten metal may leave the arc and fly in all directions. These sparks range in temperature from 2000 ° to 3000° Fahrenheit and in size from very small to as large as ¼ inch. They present a personal burn hazard plus a fire hazard if they fall on inflammable material.

The welding operator needs to protect himself, by means of a helmet and other protective devices from the harmful rays of the arc and flying sparks. The filter plates in the welding helmet will remove 99% of the harmful rays if the proper shade lens is used.

Other dangers associated with electric arc welding are:

a.  Electric shock - which may be caused by standing in damp areas, welding without gloves, bare cables, un-insulated holder, welder in wet condition etc.

b.  Harmful fumes given off in welding process especially when welding on galvanized or other coated materials.
The operator should be suitably trained with all safety precautions and take care to adequately protect himself at all times against any hazards associated with arc welding by wearing protective clothing and equipment, working in dry conditions, providing adequate ventilation and in general using good common sense.




Following is a list of safety precautions that should be observed in the use of the arc welding equipment.

a)  Electric Shock

1.  Make sure machine is properly grounded.
2.  Ensure that return earthling current is drawn from the job itself which is supposed to be welded.
3.  Proper gauge of welding cable to be used as Return earthling current.
4.  Portable ovens and other stationed ovens must be properly earthed.
5.  Welder must be “Dry” physical condition during the course of welding
6.  Never permit “live” parts of the electric welder to touch bare skin or wet clothing.

7.  Do not cool electrode holders by emersion in water.
8.  Turn off power supply when welding activity is not in use.
9.  Do not stand on wet areas while welding.
10. Wear leather gloves.
11. Make sure cable are covered and in good condition.
12. Make certain that electrode holders are properly insulate



b) Burns :-

1.  Protect eyes and face from flying particles of slag by use of proper welding shield
2.  Wear adequate protective clothing.
3.  Always wear leather gloves.
4.  Wear high top shoes.
5.  Keep collar, shirt pockets, etc. buttoned.
6.  Do not touch the electrode or metal where welding has taken place.
7.  Handle hot metal with pliers or tongs.
8.  Keep electrode stubs properly disposed of.


C) Radiant Entry ( Ultra violet rays etc...)

1.Use a welding helmet with the correct shaded welding glasses in good condition.
2.  Wear suitable clothing—do not leave bare skin exposed to the rays of the arc.
3.  Do not strike the arc without covering the face and eyes. Warn others before striking the arc.
Avoid looking directly at the arc where others are welding without proper eye protection.

d) Gases & Fumes  

1.  Work only in well-ventilated areas.
2.  Take utmost care when working on metals covered with lead or zinc, refer MSDS (Material Safety Data Sheet).
3.  If working in a confined area ensures the proper ventilation prior to start welding also use suitable respirator or other approved breathing devices as per job nature.

e) Combustible Materials :-

1.  Keep shop clean in areas where welding is to be done.
2.  Do not weld near combustible materials of any kind.
3.  Never weld on covered containers which may have held combustible and may lead to explode.

F) Fire Protection :-

1.  Be familiar with location and types of fire extinguishers
2.  Report any unsafe conditions that might start a fire.
3.  Do not weld near inflammable materials.
4.  Ensure sufficient clearance prior to weld near electrical fittings or lines, follow LOTO (Lockout/Tagout).

(Report all accidents immediately
Remember :- Accidents analysis helps in avoiding further accidents)


No comments:

Post a Comment

Yllix

amazon

Random post

Amazon Best selling Books

'; (function() { var dsq = document.createElement('script'); dsq.type = 'text/javascript'; dsq.async = true; dsq.src = '//' + disqus_shortname + '.disqus.com/embed.js'; (document.getElementsByTagName('head')[0] || document.getElementsByTagName('body')[0]).appendChild(dsq); })();

Tags

Abbreviation use for safety? (1) Accident investigation (1) Accident investigation Report? (1) Attitude (1) Authorized expose person? (1) Awareness - Electricity (1) Awareness - Malaria (1) Awareness - Swine Flu (1) Awareness - Typhoid (1) Awarness - cholara (1) Awarness message (44) Basic Electrical safety (1) Basic Orientation Training (1) Blasting awareness session (1) Carbone Monoxide (1) Chain Pulley Blocks (Do's) (1) Chain Pulley Blocks (Don'ts and Do's) (1) Classes of fire (1) communication and writen communication (1) Community unrest situation (1) competent persons? (1) Compressed Gas cylinder (1) confined space (2) confined space attendant? (1) Confined space awareness session (1) Confined space? (1) contingency plan - Accident / Incident (1) contingency plan - fire (1) contingency plan - Gas leak (1) Controlled area? (1) Cyclone (1) Defensive Driving (2) Density and specific Gravity (1) Do and Don't awareness session (1) Driving awareness session (1) Duties of a confined space attendant? (1) Earthquake (1) EHS Alert - Adverse Weather (1) EHS Alert - Air compressor (1) EHS Alert - Arc welding (1) EHS Alert - Bar Bending Machine (1) EHS Alert - Batching plant (1) EHS Alert - Cold weather (1) EHS ALERT - DENGUE (1) EHS Alert - Earth Quake (1) EHS Alert - Ebola (1) EHS Alert - Eye exposure to Portland cement (1) EHS Alert - Heat Stress (1) EHS Alert - Hot weather (1) EHS Alert - House Hold LPG (1) EHS Alert - Monsoon (1) EHS Alert - Motor cycle Helmet (1) EHS Alert - Paper (1) EHS Alert - Road / Traffic signs (1) EHS Alert - Snake Bite (1) Electrical safety (2) Electrical safety session (1) Element and Molecules (1) Emergency Evacuation Plan? (1) Employee Hand Book (1) Empty Fuel Container (1) Environment - Air pollution (1) Environment - soild waste disposal (1) Environment - Water pollution (1) Environment -Noise pollution (1) Environmental Management session (1) Ergonomics (1) Excavation safety - awareness session (1) explain each one? (1) Films (1) Fire (1) Fire fighting - Training / awareness session (1) Fire Fighting and prevention session (1) Fire Hazards and prevention (1) Fire Hazards and prevention Strategy (1) Fire Prevention session (1) Fire Protection (Do's and Dont's) (1) Fire Protection (Do's) (2) First Aid (1) First aid - Electrical (1) First aid - Electrical injuries (1) First aid - Fracture (1) First Aid – Eye Injury & Burns (1) Flood (1) Gas Cylinder Safety (Dos and Don'ts) (1) Gas Cylinder Safety (Dos) (1) Gieger meter? (1) Global warming (1) Global warming awareness (1) Grinding (Dos) (2) Grinding Safety (1) Hand-held Grinders (1) Hazardous job in a confined space? (1) Hazards (1) Hazards in a confined space (1) Heart Attack (7) Heart attack awareness session (1) Heat (1) How can extinguish and common type of fire extinguisher? (1) How is the soil classified? What is the slope to be given for each type of soil while excavating? (1) How many scaffolding tags used in scaffolding? (1) How many type of Fall Protection system? (1) How many types of accident in construction area? (1) Hydro Testing (1) Importance of Tool-box meeting (1) In what circumstances fall protection system has to be used? (1) In what situation “ear protection is needed”? (1) In which condition a scaffold cannot be erected? (1) Inspect scaffold (1) INSTRUCTION FOR STORAGE OF ELECTRICIAN’S GLOVES AND PRECAUTION S TO BE TAKEN BEFORE & AFTER USE. (1) Investigation (1) Jab safety Analysis (JSA) (1) Ladder safety (1) Ladder safety (Do's and Don'ts) (1) Ladder safety (Do's) (1) Lifting plan? (1) Lifting Tackles and chainPulley Blocks (Do's) (2) Lifting Tackles and chainPulley Blocks (Dont's) (1) lighting & unrest (1) Manual Material Handling (1) Material Handling by using cranes (3) Material safety Data sheet (MSDS) (1) Maximum distance between two adjacent accesses (1) Measuring the Radiations? (1) Mistakes (1) Mobile phone Using Tips - Awarness session (1) Monsoon Electrical safety (1) Notices (1) Nuclear Density Gauge (1) Organization Culture (1) oxygen level in a confined space (1) Petroleum act (1) Portable Electrical Tools & Electrical safety? (1) Posters (1) PPE (2) Principle of Accident Prevention (1) Radiation Hazard (1) Radiography? (2) Requirements for moving scaffold. (1) Requirements in placing an access ladder on a scaffold. (1) Requirements of a crane Lifting? (1) Requirements of a man basket? (1) RIGGING (1) Road Safety Prevention (1) Ropes and Chains (Don'ts and Do's) (1) Safe Work System (1) Safety and Maintanence Inspection (1) Safety Definitions (8) Safety during Gas cutting (1) Safety in Electricity (1) Safety in material handling (1) Safety in welding & grinding (1) Safety in welding and Gas cutting (1) Safety Poster (37) Safety poster competition (2) Safety Q&A (30) SCAFFOLD (1) Scaffolding (Do's) (2) Scaffolding (Dont's) (1) Silicosis (1) Slings inspected? (1) Slip (1) Space between the two ladder Rungs? (1) Stress Relieving (1) Summer Heat Stroke Awareness session (1) Tandum Lift? (1) THE PARTS OF CRANE? (1) Trip & Fall (1) Types of cranes? (1) Types of permits? (1) Use of accident Report? (1) Waste Management (1) Welcome to ISO -Learning session (1) Welcome to Road safety and Defensive Driving (1) Welding and Gas Cutting (3) What is near-miss? (1) What are the benefits of near-miss reporting? (1) What are the precautions to be taken for Welding? (1) What are the precautions to be taken while handling and storing compressed cylinders? (1) What are the safety requirements for doing a hot work? (1) What are the scaffoldings and its kinds and it’s Consists? (1) What are the type of fire extinguishers commonly used and briefly (1) What is a guard rail system? (1) What is a life-line? (1) WHAT IS A NEARMISS? (1) WHAT IS ACCIDENT? (1) What is an “Assembly Point" and Head counting procedure? (1) What is color coding system? (1) What is Confined Space? (2) What is different between a flash back arrestor and a check valve? (1) What is Evocation? (1) What is excavation? (1) What is Fire (1) What is First Aid and CPR? (1) What is heat stroke? What are the different stage through which a person undergoes before he gets heat stroke? (1) What is lock-out/tag-out system? (1) What is LOTO? (1) What is method statement? (1) What is MSDS ? (1) What is Radio activity? (1) What is Risk Assessment? (1) What Is Safe working Load (SWL)? (1) What is Safety? (1) What is tag system? (1) What is the emergency evacuation procedure to follow in the event of a gas release? (1) What is the responsibility of Fire Watch? (1) What is Toolbox Talks? (1) What is trench? (1) WHAT IS WASTE MANAGEMENT? (1) What safety measure are required for SAFE CRANE OPERATION (1) Who can place a scaffold tag? (1) Who is your safety officer? (1) WHO MAKES AN ACCIDENT REPORT? (1) Why Safety Training is required? (2) width of walk-way (1) Work Management System (1) work permit? (1) Work Radius? (1) Working at height (1) Working in Confined Space (1) Workplace Heat illness (1)

Blog Archive

Random post

Yllix

Random post

Random post

Flipkart